The Cast Acrylic material we use for our engraving is the same Acrylic we use for all our other acrylic products and is produced by the best companies in Europe. Thus, we can offer you a vast range of colours, opacity, thickness and also overall sizes.
In fact the thickness of our opaque acrylic starts at 3mm and goes up to 6mm for certain colours, whilst the thickness of our transparent acrylic starts at 2mm and goes up to 25mm for certain tints. Besides more than 25 different opaque colour shades and 10 different colour tints, we can also offer you Silver and Gold, both as an opaque colour and as Mirror, together with Semi- Transparent and anti- reflective Silk acrylic.
But what is the advantage of using acrylic facia for your engravings? The possibilities will become infinite. You can colour the engraved infill in any colour shade possible and combine it with the vast range of coloured facias we can offer you.
And what about the Clear Acrylic? We can engrave anything you need from the back and as the acrylic is transparent it will still show from the front whilst your lettering / logo will be safe from any vandalism. By building up colour layers on top of each other, at Skyline Plastic Works we can engrave your logos and signs in full colour and with any colour combination you require. All this engraved from the back. Click on 'Special Engravings' below for more information on the Back Engraving.
We can also provide you with an acrylic or wooden backing to finish off your sign. The
All specifications are subject to change without notice
All images (except were indicated) are copyright of Skyline Plastic Works
No unauthorised use of any material found on this web site is allowed
TOP
" We try to make the impossible possible! "
Experience & Reliability
INFORMATION
Engraved Signage on Acrylic Facia is the ideal solution for:
ILLUMINATED AND NON ILLUMINATED SIGNS
EXTERIOR AND INTERIOR INFORMATION SIGNAGE
DOOR PLAQUES
NAME PLATES AND BADGES
SMALL LABELS
INSTRUCTION PANELS
etc.
For detailed information on all the other engraving possibilities available and the materials we can offer you as facia for your engraving, please click one of the buttons below.
ENGRAVING
MATERIALS
CLICK THE IMAGES TO ENLARGE
Click the Red button for general information on our Engraving.
SPECKS
Black Opaque
3mm (1/8"), 6mm (1/4")
COLOUR / SHADE THICKNESS
White Opaque
Dark Red
Opaque
Red Opaque
Metric (Imperial)
The colours above are as accurate as your monitor display will allow. Skyline Plastic Works cannot accept any responsibility for variations between the colours above and the actual acrylic sheets. The colours above are just a representation and should be used as a guide only.
All the rectangle images can be enlarged by clicking on them
All the rectangle images can be enlarged by clicking on them
TECHNICAL
DATA
PROPERTY
Relative Density
Rockwell Hardness
Water Absorption
Flammability - 1
Flammability - 2
Flammability - 3
Tensile Strength
Tensile Modulus
Elongation at Break
Flexural Strength
Flexural Modulus
Charpy Impact Strength
Vicat Softening Point
Coefficient of Thermal Expansion
Coefficient of Thermal Conductivity
Specific Heat
Light Transmission
Refractive Index
Surface Electrical Resistivity
Electrical Strength
Poissons Ratio
UNIT
1.19 gcm ³
102 M Scale
0.21%
B2
HB
Class 3
75 MPa
3200 MPa
4%
116 MPa
3210 MPa
12 kJ.m ²
>110 °C
7.7 x 10 .K ¹
0.17 W(m.k.) ¹
1.5 J(gK) ¹
>92% in/en/bei/in 3mm
1.49
>10 m ²
15 kV.mm ¹
0.38
TEST METHOD
ISO 1183
ISO 2039-2
ISO 62
DIN 4102
UL 94
BS 476, Pt 7
ISO 527 (5mm/min)
ISO R527 (5mm/min)
ISO 527 (5mm/min)
ISO 178 (2mm/min)
ISO 178 (2mm/min)
ISO 179 (un-notched)
ISO 306A
ASTM D696
NBN B62-202
by DTA
ASTM D1003
ISO 489/A
IEC 93
IEC 243
~
Check all the technical data of our
Cast Acrylic below:
-5
-
14
-
-
The above data represents typical results obtained using standard test pieces.
The above information is given in good faith, but we are unable to guarantee its accuracy or to accept responsbility in respect of factors which are outside our knowledge or control.
